The WARN M12000 winch can manage single-line pulls with loads weighing up to 12,000 lb. Line speeds range from 30' per minute at no load to about 3.9' per minute at full load. Use this WARN winch confidently for big jobs and long pulls.
Advertising
WARN INDUSTRIES * WINCH
7
MOUNTING WINCH
MOUNTING WINCH
Choose a mounting location
that is suffi ciently strong enough
to withstand the loads you intend
to winch. Only the mounting
orientations shown are possible for
safe winching operation. All others
are improper and inappropriate.
The use of recommended bolt
and lock washer combinations
torqued to recommended levels will
prevent vibration during operation.
The mounting details indicate the
proper torque levels.
to withstand the loads you intend
to winch. Only the mounting
orientations shown are possible for
safe winching operation. All others
are improper and inappropriate.
The use of recommended bolt
and lock washer combinations
torqued to recommended levels will
prevent vibration during operation.
The mounting details indicate the
proper torque levels.
Remember the winch rope
must always spool onto the drum
as indicated by the drum rotation
decal.
as indicated by the drum rotation
decal.
Refer to the following
diagrams for proper mounting
orientation.
orientation.
WARNING
Never use bolts
that are too long.
that are too long.
Mounting Details:
(1) Smooth and fl at, thickness = 5/16” (8 mm)
(2) 7/16” (11.1 mm) lockwasher X 4
(3) 7/16-14 X 1 1/2” long, grade 5 bolt X 4
Torque 50-55 ft. lbs. (68-75Nm)
(4) 7/16” (11.1 mm) fl atwasher X 6
(5) 7/16-14 X 1 3/4” long, grade 5 bolt X 2
Torque 50-55 ft. lbs. (68-75Nm)
(1) Smooth and fl at, thickness = 5/16” (8 mm)
(2) 7/16” (11.1 mm) lockwasher X 4
(3) 7/16-14 X 1 1/2” long, grade 5 bolt X 4
Torque 50-55 ft. lbs. (68-75Nm)
(4) 7/16” (11.1 mm) fl atwasher X 6
(5) 7/16-14 X 1 3/4” long, grade 5 bolt X 2
Torque 50-55 ft. lbs. (68-75Nm)
Control Pack Installation
Mount the control pack
according to the instructions
included in the WARN mounting
system kit. Use the bracket
included in the kit.
included in the WARN mounting
system kit. Use the bracket
included in the kit.
The control pack mounting
fasteners may also be moved to
the unused holes in the control
pack base plate for additional
mounting fl exibility.
the unused holes in the control
pack base plate for additional
mounting fl exibility.
Mounting Bolt Pattern:
10” x 4.5”, 254 mm x 114.3 mm
10” x 4.5”, 254 mm x 114.3 mm
WARNING
Always choose
a mounting
location that is
suffi ciently strong
to withstand the
maximum pulling
capacity of your
winch.
a mounting
location that is
suffi ciently strong
to withstand the
maximum pulling
capacity of your
winch.
WARNING
Always complete
the winch
installation and
attach the hook
before installing
the wiring.
the winch
installation and
attach the hook
before installing
the wiring.
Plate Thickness
Bolt Length
5/16” (8 mm)
1.5” (40 mm)
3/8” (10 mm)
1.5” (40 mm)
1/2” (13 mm)
1.75” (45 mm)
WARN INDUSTRIES * WINCH
8
ELECTRICAL CONNECTIONS
Electrical Diagrams:
ELECTRICAL CONNECTIONS
Use the included insulating
boots on exposed connections to
prevent electrical shorting. Route
battery connection cables in areas
which will not cause them to
chafe or cut through the insulation
causing a potential short circuit.
prevent electrical shorting. Route
battery connection cables in areas
which will not cause them to
chafe or cut through the insulation
causing a potential short circuit.
Upon completion of
installation, check winch for proper
operation.
operation.
WARNING
Never route
electrical cables
across sharp
edges.
electrical cables
across sharp
edges.
WARNING
Never
route
electrical cables
near parts that
get hot.
near parts that
get hot.
WARNING
Never
route
electrical cables
through or near
moving parts.
through or near
moving parts.
WARNING
Always place
the supplied
terminal boots
on wires and
terminals as
directed by
the installation
instructions.
the supplied
terminal boots
on wires and
terminals as
directed by
the installation
instructions.
Battery Recommendations
A fully charged battery and
good connections are essential
to the proper operation of your
winch. The minimum requirement
for a 12 volt DC battery is 650 Cold
Cranking Amps.
to the proper operation of your
winch. The minimum requirement
for a 12 volt DC battery is 650 Cold
Cranking Amps.
WARNING
Always insulate
and protect all
exposed wiring
and electrical
terminals.
and protect all
exposed wiring
and electrical
terminals.
Pin #
Color
1
Brown
2
White
3
Black
4
Green
5
6
Red
1
2
3
3
6
5
5
4
Black
Red
White
Brown
Green
A
F1
F2
Advertising
This manual is related to the following products:
Popular Brands
Popular manuals